Album Electronics kits from .:madworm:.

CPLD training board

nobody@ipernity.com (.:madworm:.) — Sat, 28 Jan 2017 10:20:37 +0000

.:madworm:. has posted:

www.tindie.com/products/microwavemont/vhdl-training-board

7805 from hell

nobody@ipernity.com (.:madworm:.) — Thu, 02 Oct 2014 13:56:01 +0000

.:madworm:. has posted:

DO NOT BUY!

Assembly tools

nobody@ipernity.com (.:madworm:.) — Tue, 29 May 2012 22:45:47 +0000

.:madworm:. has posted:

Thin solder wire, flux and a good pair of tweezers.

Half-Ohm mΩ DMM adapter

nobody@ipernity.com (.:madworm:.) — Wed, 22 May 2013 15:27:18 +0000

.:madworm:. has posted:

It works very well. Made by Jaanus Kalde.

Half-Ohm mΩ DMM adapter

nobody@ipernity.com (.:madworm:.) — Wed, 22 May 2013 15:27:18 +0000

.:madworm:. has posted:

It works very well. Made by Jaanus Kalde.

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:11 +0000

.:madworm:. has posted:

Very easy to build. The micro comes pre-programmed.

My custom PWM-enabled firmware: github.com/madworm/ledcandle

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:12 +0000

.:madworm:. has posted:

Tiny resistors

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:13 +0000

.:madworm:. has posted:

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:13 +0000

.:madworm:. has posted:

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:14 +0000

.:madworm:. has posted:

Tiny 1k resistor

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:15 +0000

.:madworm:. has posted:

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:16 +0000

.:madworm:. has posted:

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:17 +0000

.:madworm:. has posted:

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:17 +0000

.:madworm:. has posted:

Very easy to build. The micro comes pre-programmed.

My custom PWM-enabled firmware: github.com/madworm/ledcandle

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 01:09:18 +0000

.:madworm:. has posted:

Very easy to build. The micro comes pre-programmed.

My custom PWM-enabled firmware: github.com/madworm/ledcandle

Akafugu LED candle

nobody@ipernity.com (.:madworm:.) — Tue, 07 May 2013 08:53:17 +0000

.:madworm:. has posted:

Very easy to build. The micro comes pre-programmed.

My custom PWM-enabled firmware: github.com/madworm/ledcandle

JyeTech cap-meter 1000µF

nobody@ipernity.com (.:madworm:.) — Wed, 15 Aug 2012 09:28:35 +0000

.:madworm:. has posted:

Officially it supports 1pF to 500µF with auto-ranging. It also measured a 1000µF cap, but locked up after that. Can't blame it for that I think. Auto-ranging is pretty quick with small capacitances.

JyeTech cap-meter 10nF

nobody@ipernity.com (.:madworm:.) — Wed, 15 Aug 2012 09:28:34 +0000

.:madworm:. has posted:

Works very well in the supported 1pF to 500µF range.

JyeTech cap-meter 22pF

nobody@ipernity.com (.:madworm:.) — Wed, 15 Aug 2012 09:28:33 +0000

.:madworm:. has posted:

Works very well in the supported 1pF to 500µF range.

JyeTech cap-meter + slider

nobody@ipernity.com (.:madworm:.) — Wed, 15 Aug 2012 09:28:32 +0000

.:madworm:. has posted:

I got this little capacitance meter (just 8€) for measuring the variable capacitance of a capacitive-slider test board. Now I can choose the right size storage capacitor for it. The pad pattern I chose seems to be a bit too large. It does matter quite a lot how much contact the finger makes. Hopefully I will get better results when I evaluate both pads and use the difference value.