Album Misc Tools from .:madworm:.

70€ circle cutter

nobody@ipernity.com (.:madworm:.) — Fri, 04 Sep 2009 14:40:53 +0000

So this is it. After I wasn't successful with the hole punch, I thought this would solve my problems for good.

It cuts circles, but the forces are so big, that the centering ping moves around in the plastic foil. Therefore it cuts nice 'wanna be' circles, or egg shaped things. The edges are almost perfect though.

EPIC FAILURE V2.0

I need to find a small company/workshop with some sort of hydraulic press. "punch, lift and slide" ;-)

Didn't test any of it

nobody@ipernity.com (.:madworm:.) — Fri, 11 May 2012 18:08:19 +0000

.:madworm:. has posted:

Blah blah blah, yak yak yak.

Spirit level - bottom side

nobody@ipernity.com (.:madworm:.) — Wed, 10 Aug 2011 21:19:53 +0000

.:madworm:. has posted:

Spirit level + my grubby finger

nobody@ipernity.com (.:madworm:.) — Wed, 10 Aug 2011 21:20:32 +0000

.:madworm:. has posted:

What am I?

nobody@ipernity.com (.:madworm:.) — Sat, 18 Jun 2011 15:31:22 +0000

.:madworm:. has posted:

I am made of brass and SiO2.

70€ circle cutter

nobody@ipernity.com (.:madworm:.) — Fri, 04 Sep 2009 14:40:51 +0000

.:madworm:. has posted:

70€ circle cutter

nobody@ipernity.com (.:madworm:.) — Fri, 04 Sep 2009 14:40:55 +0000

.:madworm:. has posted:

70€ circle cutter

nobody@ipernity.com (.:madworm:.) — Fri, 04 Sep 2009 14:40:57 +0000

.:madworm:. has posted:

70€ circle cutter

nobody@ipernity.com (.:madworm:.) — Fri, 04 Sep 2009 14:40:59 +0000

.:madworm:. has posted:

Hollow punch - 35mm

nobody@ipernity.com (.:madworm:.) — Wed, 19 Aug 2009 18:37:31 +0000

.:madworm:. has posted:

The biggest hollow punch is quite dull.

Hollow punch - 5mm

nobody@ipernity.com (.:madworm:.) — Wed, 19 Aug 2009 18:37:32 +0000

.:madworm:. has posted:

The smallest hollow punch is quite sharp.

Hollow punch set

nobody@ipernity.com (.:madworm:.) — Wed, 19 Aug 2009 18:37:36 +0000

.:madworm:. has posted:

The biggest hollow punch in there is what I need, but it is too dull.

Dial caliper

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:51 +0000

.:madworm:. has posted:

Caliper

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:50 +0000

.:madworm:. has posted:

Caliper

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:50 +0000

.:madworm:. has posted:

The strip of copper is used to lock the sliding part without scratching it.

Dial caliper mechanism

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:49 +0000

.:madworm:. has posted:

Dial caliper mechanism

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:48 +0000

.:madworm:. has posted:

Dial caliper mechanism

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:47 +0000

.:madworm:. has posted:

If the anti-backlash spring is pretensioned during assembly, there is no backlash.

Caliper mechanism

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:46 +0000

.:madworm:. has posted:

If the anti-backlash spring is pretensioned during assembly, there is no backlash.

Dial caliper mechanism

nobody@ipernity.com (.:madworm:.) — Sun, 28 Oct 2012 14:40:45 +0000

.:madworm:. has posted:

The two small gears 'ride' on the rack gear of the caliper. If assembled correctly there is no backlash.