Photos, videos and docs of GrahamH, with the keywords: "cable"

Connections 20220719 16 09 52 Pro

nobody@ipernity.com (GrahamH) — Wed, 29 Mar 2023 04:17:56 +0000

GrahamH has posted:

A connections point which parallels sound board input cables from another bank of 4 inputs at my church. This was done to improve operating flexibility. July 2022.

VGA Lead 0617 2251

nobody@ipernity.com (GrahamH) — Sat, 10 Jun 2017 10:11:36 +0000

GrahamH has posted:

I needed a longer VGA cable so I took two leads from old CRT monitors and worked out how they needed to be joined. I then soldered the wires insulating each joint with heatshrink sleeving. A larger diameter sleeve was put over the joints and then for additional protection was wrapped in a tape usually used for sealing antenna cable connections on radio towers. A loop was made and the same tape secured it to prevent straining the soldered joints. June 2017.

VGA Lead 0617 2244

nobody@ipernity.com (GrahamH) — Sat, 10 Jun 2017 10:09:38 +0000

GrahamH has posted:

WipeJoint122015 0929

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 02:04:52 +0000

GrahamH has posted:

Both cables are now repaired and holding air pressure. The schrader valves enable pressure to be measured, estimated by testing for outflow or used to attach a cylinder of compressed dry air if the supply fed through the cable from the telephone exchange is isolated. See notes.

The fibre cables will not be returned to the pit but will remain on the ground until more pits or some other solution to the lack of space is found.

The jointer uses an LPG torch to melt solder (60 lead/ 40 tin) which is wiped around the cable, using a piece of hide to build a thickness of solder which seals the cable and gives some strength to the joint. Sterene, a fat based product, is melted onto the work to assist the wiping process.

Paper insulated lead-covered cable was damaged by NBN builders placing too much gear in the cable pit. Cable jointers from Telstra are repairing the water-damaged circuits. They were working at this and another nearby junction pit and pillar.

WipeJoint122015 0928

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 02:02:28 +0000

GrahamH has posted:

Joint housing for fibre cables for the NBN.

WipeJoint122015 0927

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 02:00:51 +0000

GrahamH has posted:

Making sure the underneath is correctly completed.

The jointer uses an LPG torch to melt solder (60 lead/ 40 tin) which is wiped around the cable, using a piece of hide to build a thickness of solder which seals the cable and gives some strength to the joint. Sterene, a fat based product, is melted onto the assist the wiping process.

Paper insulated lead-covered cable was damaged by NBN builders placing too much gear in the cable pit. Cable jointers from Telstra are repairing the water-damaged circuits. They were working at this and another nearby junction pit and pillar.

WipeJoint122015 0926

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:59:13 +0000

GrahamH has posted:

It's difficult to repair the underside of the joint because of both working out of sight and working up hill.

The jointer uses an LPG torch to melt solder (60 lead/ 40 tin) which is wiped around the cable, using a piece of hide to build a thickness of solder which seals the cable and gives some strength to the joint. Sterene, a fat based product, is melted onto the assist the wiping process.

Paper insulated lead-covered cable was damaged by NBN builders placing too much gear in the cable pit. Cable jointers from Telstra are repairing the water-damaged circuits. They were working at this and another nearby junction pit and pillar.

WipeJoint122015 0925

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:57:16 +0000

GrahamH has posted:

The second man is assisting by keeping the heat of the torch away from the other cables.

See note.

The jointer uses an LPG torch to melt solder (60 lead/ 40 tin) which is wiped around the cable, using a piece of hide to build a thickness of solder which seals the cable and gives some strength to the joint. Sterene, a fat based product, is melted onto the assist the wiping process.

Paper insulated lead-covered cable was damaged by NBN builders placing too much gear in the cable pit. Cable jointers from Telstra are repairing the water-damaged circuits. They were working at this and another nearby junction pit and pillar.

WipeJoint122015 0924

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:55:39 +0000

GrahamH has posted:

The jointer uses an LPG torch to melt solder (60 lead/ 40 tin) which is wiped around the cable, using a piece of hide to build a thickness of solder which seals the cable and gives some strength to the joint. Sterene, a fat based product, is melted onto the assist the wiping process.

Paper insulated lead-covered cable was damaged by NBN builders placing too much gear in the cable pit. Cable jointers from Telstra are repairing the water-damaged circuits. They were working at this and another nearby junction pit and pillar.

WipeJoint122015 0923

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:54:09 +0000

GrahamH has posted:

WipeJoint122015 0922

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:52:41 +0000

GrahamH has posted:

WipeJoint122015 0921

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:51:06 +0000

GrahamH has posted:

WipeJoint122015 0920

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:49:30 +0000

GrahamH has posted:

WipeJoint122015 0919

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:47:54 +0000

GrahamH has posted:

WipeJoint122015 0918

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:46:19 +0000

GrahamH has posted:

WipeJoint122015 0917

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:44:54 +0000

GrahamH has posted:

WipeJoint122015 0916

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:43:33 +0000

GrahamH has posted:

WipeJoint122015 0915

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:42:02 +0000

GrahamH has posted:

WipeJoint122015 0914

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:40:33 +0000

GrahamH has posted:

WipeJoint122015 0911

nobody@ipernity.com (GrahamH) — Sat, 02 Jan 2016 01:38:51 +0000

GrahamH has posted: